Name
conntrack — shorewall6 conntrack file
Synopsis
/etc/shorewall6/conntrack
Description
The original intent of the notrack file was to exempt certain traffic from Netfilter connection tracking. Traffic matching entries in the file were not to be tracked.
The role of the file was expanded in Shorewall 4.4.27 to include all rules that can be added in the Netfilter raw table. In 4.5.7, the file's name was changed to conntrack.
The file supports two different column layouts: FORMAT 1, FORMAT 2, and FORMAT 3, FORMAT 1 being the default. The three differ as follows:
in FORMAT 2 and 3, there is an additional leading ACTION column.
in FORMAT 3, the SOURCE column accepts no zone name; rather the ACTION column allows a SUFFIX that determines the chain(s) that the generated rule will be added to.
When an entry in the following form is encountered, the format of
the following entries are assumed to be of the specified
format.
[?]FORMAT
format |
where format is either 1,2 or 3.
Format 3 was introduced in Shorewall 4.5.10. The optional '?' was introduced in Shorewall 4.5.11 and ?FORMAT is the preferred form; the form without the '?' is deprecated.
Comments may be attached to Netfilter rules generated from entries in this file through the use of COMMENT lines. These lines begin with the word COMMENT; the remainder of the line is treated as a comment which is attached to subsequent rules until another COMMENT line is found or until the end of the file is reached. To stop adding comments to rules, use a line with only the word COMMENT.
Note
Beginning with Shorewall 4.5.11, ?COMMENT is a synonym for COMMENT and is preferred.
The columns in the file are as follows (where the column name is followed by a different name in parentheses, the different name is used in the alternate specification syntax).
- ACTION - {NOTRACK|CT:helper:
name[(arg=val[,...])|CT:ctevents:event[,...]|CT:expevents:new|notrack|DROP|LOG|NFLOG(nflog-parameters)|IP6TABLES(target)}[:log-level[:log-tag]][:chain-designator] This column is only present when FORMAT >= 2. Values other than NOTRACK require CT Target support in your iptables and kernel.
NOTRACKorCT:notrackDisables connection tracking for this packet. If a
log-levelis specified, the packet will also be logged at that level.helper:nameAttach the helper identified by the
nameto this connection. This is more flexible than loading the conntrack helper with preset ports. If alog-levelis specified, the packet will also be logged at that level.At this writing, the available helpers are:
- amanda
Requires that the amanda netfilter helper is present.
- ftp
Requires that the FTP netfilter helper is present.
- irc
Requires that the IRC netfilter helper is present.
- netbios-ns
Requires that the netbios_ns (sic) helper is present.
- RAS and Q.931
These require that the H323 netfilter helper is present.
- pptp
Requires that the pptp netfilter helper is present.
- sane
Requires that the SANE netfilter helper is present.
- sip
Requires that the SIP netfilter helper is present.
- snmp
Requires that the SNMP netfilter helper is present.
- tftp
Requires that the TFTP netfilter helper is present.
May be followed by an option list of
arg=valpairs in parentheses:ctevents=event[,...]Only generate the specified conntrack events for this connection. Possible event types are: new, related, destroy, reply, assured, protoinfo, helper, mark (this is connection mark, not packet mark), natseqinfo, and secmark. If more than one event is listed, the
eventlist must be enclosed in parentheses (e.g., ctevents=(new,related)).expevents=newOnly generate new expectation events for this connection.
ctevents:
event[,...]Added in Shorewall 4.6.10. Only generate the specified conntrack events for this connection. Possible event types are: new, related, destroy, reply, assured, protoinfo, helper, mark (this is connection mark, not packet mark), natseqinfo, and secmark.
expevents=new
Added in Shorewall 4.6.10. Only generate new expectation events for this connection.
DROPAdded in Shorewall 4.5.10. Silently discard the packet. If a
log-levelis specified, the packet will also be logged at that level.IP6TABLES(target)Added in Shorewall 4.6.0. Allows you to specify any iptables
targetwith target options (e.g., "IP6TABLES(AUDIT --type drop)"). If the target is not one recognized by Shorewall, the following error message will be issued:ERROR: Unknown target ( target)This error message may be eliminated by adding
targetas a builtin action in shorewall6-actions(5).LOGAdded in Shoreawll 4.6.0. Logs the packet using the specified
log-levelandlog-tag(if any). If no log-level is specified, then 'info' is assumed.NFLOGAdded in Shoreawll 4.6.0. Queues the packet to a backend logging daemon using the NFLOG netfilter target with the specified
nflog-parameters.
When FORMAT = 1, this column is not present and the rule is processed as if NOTRACK had been entered in this column.
Beginning with Shorewall 4.5.10, when FORMAT = 3, this column can end with a colon followed by a
chain-designator. Thechain-designatorcan be one of the following:- P
The rule is added to the raw table PREROUTING chain. This is the default if no
chain-designatoris present.- O
The rule is added to the raw table OUTPUT chain.
- PO or OP
The rule is added to the raw table PREROUTING and OUTPUT chains.
- SOURCE (formats 1 and 2) ‒ zone[:interface][:address-list]
where
zoneis the name of a zone,interfaceis an interface to that zone, andaddress-listis a comma-separated list of addresses (may contain exclusion - see shorewall6-exclusion (5)).Beginning with Shorewall 4.5.7,
allcan be used as thezonename to mean all zones.Beginning with Shorewall 4.5.10,
all-can be used as thezonename to mean all off-firewall zones.- SOURCE (format 3) ‒
{-|interface[:address-list]|
address-list} Where
interfaceis an interface to that zone, andaddress-listis a comma-separated list of addresses (may contain exclusion - see shorewall6-exclusion (5)).COMMENT is only allowed in format 1; the remainder of the line is treated as a comment that will be associated with the generated rule(s).
- DEST ‒
{-|interface[:address-list]|
address-list} where
address-listis a comma-separated list of addresses (may contain exclusion - see shorewall6-exclusion (5)).- PROTO ‒
protocol-name-or-number[,...] A protocol name from
/etc/protocolsor a protocol number.Beginning with Shorewall 4.5.12, this column can accept a comma-separated list of protocols.
- DEST PORT(S) (dport) -
{-|
port-number/service-name-list|+ipset} A comma-separated list of port numbers and/or service names from
/etc/services. May also include port ranges of the formlow-port:high-portif your kernel and iptables include port range support.Beginning with Shorewall 4.6.0, an ipset name can be specified in this column. This is intended to be used with bitmap:port ipsets.
- SOURCE PORT(S) (sport) -
{-|
port-number/service-name-list|+ipset} A comma-separated list of port numbers and/or service names from
/etc/services. May also include port ranges of the formlow-port:high-portif your kernel and iptables include port range support.Beginning with Shorewall 4.5.15, you may place '=' in this column, provided that the DEST PORT(S) column is non-empty. This causes the rule to match when either the source port or the destination port in a packet matches one of the ports specified in DEST PORTS(S).
Beginning with Shorewall 4.6.0, an ipset name can be specified in this column. This is intended to be used with bitmap:port ipsets.
- USER/GROUP (user) ‒
[
user][:group] May only be specified if the SOURCE
zoneis $FW. Specifies the effective user id and or group id of the process sending the traffic.- SWITCH -
[!]
switch-name[={0|1}] Added in Shorewall6 4.5.10 and allows enabling and disabling the rule without requiring shorewall6 restart.
Enables the rule if the value stored in
/proc/net/nf_condition/is 1. Disables the rule if that file contains 0 (the default). If '!' is supplied, the test is inverted such that the rule is enabled if the file contains 0.switch-nameWithin the
switch-name, '@0' and '@{0}' are replaced by the name of the chain to which the rule is a added. Theswitch-name(after '@...' expansion) must begin with a letter and be composed of letters, decimal digits, underscores or hyphens. Switch names must be 30 characters or less in length.Switches are normally off. To turn a switch on:
echo 1 > /proc/net/nf_condition/ switch-nameTo turn it off again:
echo 0 > /proc/net/nf_condition/ switch-nameSwitch settings are retained over shorewall6 restart.
When the
switch-nameis followed by=0or=1, then the switch is initialized to off or on respectively by the start command. Other commands do not affect the switch setting.
EXAMPLES
Example 1:
Use the FTP helper for TCP port 21 connections from the firewall itself.
FORMAT 2 #ACTION SOURCE DEST PROTO DEST SOURCE USER/GROUP # PORT(S) PORT(S) CT:helper:ftp(expevents=new) fw - tcp 21
Example 2 (Shorewall 4.5.10 or later):
Drop traffic to/from all zones to IP address 2001:1.2.3::4
FORMAT 2 #ACTION SOURCE DEST PROTO DEST SOURCE USER/GROUP # PORT(S) PORT(S) DROP all-:2001:1.2.3::4 - DROP all 2001:1.2.3::4
or
FORMAT 3 #ACTION SOURCE DEST PROTO DEST SOURCE USER/GROUP # PORT(S) PORT(S) DROP:P 2001:1.2.3::4 - DROP:PO - 2001:1.2.3::4
See ALSO
http://www.shorewall.net/configuration_file_basics.htm#Pairs
shorewall6(8), shorewall6-accounting(5), shorewall6-actions(5), shorewall6-blacklist(5), shorewall6-hosts(5), shorewall6-interfaces(5), shorewall6-ipsec(5), shorewall6-netmap(5),shorewall6-params(5), shorewall6-policy(5), shorewall6-providers(5), shorewall6-proxyarp(5), shorewall6-rtrules(5), shorewall6-routestopped(5), shorewall6-rules(5), shorewall6.conf(5), shorewall6-secmarks(5), shorewall6-tcclasses(5), shorewall6-tcdevices(5), shorewall6-mangle(5), shorewall6-tos(5), shorewall6-tunnels(5), shorewall-zones(5)
